Showing results: 346 - 360 of 400 items found.
-
Wayfind'r -
Timco Instruments, LLC
The WAYFIND'R Impulse Cable Tracer was originally designed for electric utility use to accurately identify the route of buried secondary cables. Because the WAYFIND'R imposes an audio frequency signal on the cable, the signal is not induced into adjacent cables or pipes, eliminating false signals. The WAYFIND'R may also be used fro tracing indoor wiring and buried shielded primary cables.
-
NCT-100-S -
ShinewayTech
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
TG 600 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR TG 600. The TG 600 audio frequency transmitter was designed specifically for the precise location of cable faults and joints using the twist method. The display of the input and output current makes selection of the correct adjustment easier.* High-performance audio frequency transmitter up to 600 VA* Frequency of 2 or 10 kHz, quartz-stabilised (other frequencies on request)* Potential-free output* Impedance adjustment in 8 steps from 0.3 to 300 Ω
-
Analog Devices Inc.
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
TM520 -
T&M Tools Limited Co
Coordinating with high-voltage signal generator, test sound and magnet simultaneously, locate high-resistance and arc-over fault of the power cable. While fixing the fault point, the instrument can test the cable path as well.Coordinating with audio-frequency signal generator, test audio frequency induction, locate low-resistance fault, and identify the cable and test the depth of it.
-
72-6792 -
Tenma
*Electronically locates hidden cables gas and water pipes*Traces hidden ceiling joists and wall studs*Senses presence of mains power withut touching live wires*Locates breaks in circuits and cables*Identifies faulty plugs switches and sockets*Incorporates audio signal and indicator light
-
Virtins Technology
1) Measurement microphone and its accessories (a windshield and a microphone clip)2) XLR-to-USB Converter3) USB cable (1.5 m) 4) CD (contains the copy-protected Multi-Instrument Software) 5) USB hardkey (contains a Multi-Instrument Standard License)6) Audio Test CD (contains a list of audio test tones and noises) (AudioTestCD.zip or AudioTestCD.rar)7) 1/8” TRS cable (1.8m) 8) Black Soft Pouch Case 9) Individual Sound Level Calibration Data 10) Individual Microphone Calibration Data (only provided in RTA-168B)11) A small microphone stand
-
Cable Nooks -
ALTINEX, Inc.
Designed for boardrooms and conference rooms, the modular Cable-Nook provides a simple and effective way of hiding/storing multimedia cables and connectors. The cables remain connected to a presentation system enabling the user to access connections to video, audio, and other media sources. The modular Cable-Nook uses a half-moon lid that remains flush with the table when not in use. To access the cables or connectors, simply lift the door and pull the cable ends out, or plug computer video cables into any installed fixed connectors. The lid closes easily even with several cables in use. After the presentation, the cable ends are returned to the Cable-Nook for safe storage.
-
NTi Audio AG
The microphone bodies contain the preamplifier. They combine high dynamic range and wide frequency range with low noise. These measurement microphones connect via the ASD Cable to the XL2 Audio and Acoustic Analyzer, e.g. for measurements at remote locations or to reduce acoustic reflections.
-
ST-C6HD-150-LC -
Network Technologies Inc
The XTENDEX® Low-Cost HDMI Extender transmits digital video and audio signals up to 150 feet using one CAT5e/6 cable. Each video extender consists of a local unit that connects to an HDMI source and a remote unit that connects to an HDMI display.
-
AmpConnect™ ISC -
Listen Inc
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Easy Touch -
Cirris Systems Corporation
Test all your cable or harness designs quickly and confidently with our newest cable and harness tester. EasyTouch checks for opens, shorts, and miswires and performs IR/DWV testing up to 2000Vdc (1000VAC Optional). Easy Touch features an integrated Windows 7 PC complete with hard drive, VGA, USB, Ethernet, and audio ports and a large 10.4" graphical touch-screen display.
-
250 SSP -
Aines Manufacturing Corp.
This probe is designed for those technicians that want the best tool available. The Model 250SSP is supplied with a cone-shaped tip and a duckbill tip that is longer and flatter, permitting insertion into larger cables, or cables under tension where slack cannot be obtained. Another feature is the built in speaker for audio without the need for a butt set or headset. The speaker is operated by a slide switch that has a "lock" position for continuous monitoring.
-
C3121P -
COMET SYSTEM, s.r.o.
Thermometer, hygrometer is designed for direct measurement of temperature, relative humidity for compressed air up to 25 bars with 1m cable. Audio and optical alarm of measured values. Memory of minimum and maximum measured values. Function Hold - manual storing of actual values for later displaying.
-
Avenue -
Ensemble Designs, Inc.
The Avenue system includes modules for video up/down conversion, audio embedding, synchronization, conversion, routing, noise reduction, protection switches, test signal generators and more. Avenue signal processing modules are used worldwide in broadcast, mobile, satellite, cable, worship and post production facilities. Avenue is a tray-based signal integration system housed in a 1RU or 3RU frame. Any combination of 1.5 Gb/s HD, 3 Gb/s HD, SD, MPEG, analog video and audio processing modules can be used together in the same frame.